Alert: Notifications and correspondence during COVID-19 restrictions
We are operating at reduced capacity due to the COVID 19 Alert Level Two requirements. Find out more about how to correspond and notify us during this time.
This safety alert highlights the serious health and safety risks of exposure to high levels of respirable crystalline silica (RCS) for those who work in the stone benchtop industry.
Silicosis is an irreversible and progressive disease that causes fibrosis of the lungs from the inhalation of RCS. The only treatment for advanced disease is lung transplant.
As of February 2019, 99 confirmed cases of silicosis associated with engineered stone benchtop work had been identified in Queensland, Australia. The vast majority of these cases were in workers with no symptoms of disease.
Many of these cases have been consistent with accelerated silicosis, a form of the disease which develops over a short period (1 to 10 years) from inhalation of very high concentrations of RCS.
In New Zealand the prevalence of silicosis is currently unknown. This safety alert has been issued to raise awareness of the risks to those working in the engineered stone industry.
What we know
Engineered stone benchtops have become increasingly popular for kitchens and bathrooms. They are made by mixing finely crushed rock with a polymeric resin, then moulded into slabs and heat-cured. The silica content of engineered stone is approximately 90% silica, which is much higher than natural stones.
Workers may be exposed to RCS while cutting, grinding, sanding and polishing stone benchtops during manufacturing and installation. Accelerated silicosis is one of three forms of silicosis that has been recently reported in workers working with engineered stone.
Accelerated silicosis results from the inhalation of very high concentrations of silica dust. It develops in a pattern similar to that of simple silicosis, except the time from initial exposure to the onset of disease is shorter and the progression to complicated silicosis is more rapid. Specifically, nodules increase in size and merge into large lesions, leading to progressive massive fibrosis and ultimately cardio respiratory failure.
Before starting work using engineered stone, businesses must complete a risk assessment and review their controls. It is important to eliminate uncontrolled dry cutting, grinding or polishing of engineered stone.
If this is not reasonably practicable then exposures must be minimised. Options include:
- substituting engineered stone for materials with a lower silica content
- isolating work areas or tasks that generate dust using physical barriers or computer numerical control (CNC) machines
- using engineering controls, such as local exhaust ventilation (LEV), water suppression (wet cutting), or on-tool dust extraction attachments. Wet sprays should be controlled by guards to prevent dust becoming airborne and wet waste must be managed. LEV system dust collectors or vacuums should be H-class HEPA filtered. Any LEV must be effective, fit for purpose, installed, set up and used correctly and maintained so that it remains effective
- further minimisation controls include administrative controls, such as good housekeeping practice (wet wiping, using an H-class HEPA-filtered vacuum, and low-pressure water cleaning – dry wiping or sweeping is not appropriate).
If a risk still remains, use the appropriate personal protective equipment:
- use a suitable respirator with a filter cartridge with the appropriate assigned protection factor; the appropriate respirator and filter cartridge combination will be informed by exposure monitoring
- ensure the respirator is fit-tested for the worker, cleaned and maintained properly
- wear suitable work clothing such as coveralls that are disposable or can be laundered at the workplace to avoid taking them home.
The current New Zealand Workplace Exposure Standard (WES) for RCS (quartz) is 0.05 mg/m3. This value was reduced from 0.1 mg/m3 in November following consultation.
You can engage an occupational hygienist from the New Zealand Occupational Hygiene Society(external link) (NZOHS), or from the Health and Safety Association of New Zealand (HASANZ) Register(external link) to measure RCS concentrations and to help evaluate risks to worker health.
Response and updates
We’re working with medical and health and safety professionals on a coordinated response for workers at high risk of exposure to dust from engineered stone.
If you're interested in receiving this information when it is available, and other accelerated silicosis updates, you can record your details in our online form.
We provide further guidance related to accelerated silicosis:
- Silica dust in the workplace
- 8 key things for workers to know: Controlling silica dust in the workplace
- Controlling construction dust with on-tool extraction
- Exposure Monitoring under the Health and Safety at Work (General Risk and Workplace Management) Regulations 2016
- Health monitoring required under the Health and Safety at Work (General Risk and Workplace Management) Regulations 2016